|
This HTML version of the file intel.doc from the
PC Game Programmer's guide was produced by Zack T Smith. Fancy HTML modifications are copyright ©
2005 by Zack T Smith, all rights reserved.
This information is provided in the hope that it will be useful,
but without any warranty. It is provided AS-IS,
without even the implied warranty of fitness for a particular purpose.
I Instructions
IDIV - Signed Integer Division
Usage: IDIV src
Modifies flags: (AF,CF,OF,PF,SF,ZF undefined)
Signed binary division of accumulator by source. If source is a
byte value, AX is divided by "src" and the quotient is stored in
AL and the remainder in AH. If source is a word value, DX:AX is
divided by "src", and the quotient is stored in AL and the
remainder in DX.
Clocks Size
Operands 808x 286 386 486 Bytes
reg8 101-112 17 19 19 2
reg16 165-184 25 27 27 2
reg32 - - 43 43 2
mem8 (107-118)+EA 20 22 20 2-4
mem16 (171-190)+EA 38 30 28 2-4 (W88=175-194)
mem32 - - 46 44 2-4
IMUL - Signed Multiply
Usage: IMUL src
IMUL src,immed (286+)
IMUL dest,src,immed8 (286+)
IMUL dest,src (386+)
Modifies flags: CF OF (AF,PF,SF,ZF undefined)
Signed multiplication of accumulator by "src" with result placed
in the accumulator. If the source operand is a byte value, it
is multiplied by AL and the result stored in AX. If the source
operand is a word value it is multiplied by AX and the result is
stored in DX:AX. Other variations of this instruction allow
specification of source and destination registers as well as a
third immediate factor.
Clocks Size
Operands 808x 286 386 486 Bytes
reg8 80-98 13 9-14 13-18 2
reg16 128-154 21 9-22 13-26 2
reg32 - - 9-38 12-42 2
mem8 86-104 16 12-17 13-18 2-4
mem16 134-160 24 12-25 13-26 2-4
mem32 - - 12-41 13-42 2-4
reg16,reg16 - - 9-22 13-26 3-5
reg32,reg32 - - 9-38 13-42 3-5
reg16,mem16 - - 12-25 13-26 3-5
reg32,mem32 - - 12-41 13-42 3-5
reg16,immed - 21 9-22 13-26 3
reg32,immed - 21 9-38 13-42 3-6
reg16,reg16,immed - 2 9-22 13-26 3-6
reg32,reg32,immed - 21 9-38 13-42 3-6
reg16,mem16,immed - 24 12-25 13-26 3-6
reg32,mem32,immed - 24 12-41 13-42 3-6
IN - Input Byte or Word From Port
Usage: IN accum,port
Modifies flags: None
A byte, word or dword is read from "port" and placed in AL, AX or
EAX respectively. If the port number is in the range of 0-255
it can be specified as an immediate, otherwise the port number
must be specified in DX. Valid port ranges on the PC are 0-1024,
though values through 65535 may be specified and recognized by
third party vendors and PS/2's.
Clocks Size
Operands 808x 286 386 486 Bytes
accum,immed8 10/14 5 12 14 2
accum,immed8 (PM) 6/26 8/28/27 2
accum,DX 8/12 5 13 14 1
accum,DX (PM) 7/27 8/28/27 1
- 386+ protected mode timings depend on privilege levels.
first number is the timing if: CPL ≤ IOPL
second number is the timing if: CPL > IOPL or in VM 86 mode (386)
CPL ≥ IOPL (486)
third number is the timing when: virtual mode on 486 processor
- 486 virtual mode always requires 27 cycles
INC - Increment
Usage: INC dest
Modifies flags: AF OF PF SF ZF
Adds one to destination unsigned binary operand.
Clocks Size
Operands 808x 286 386 486 Bytes
reg8 3 2 2 1 2
reg16 3 2 2 1 1
reg32 3 2 2 1 1
mem 15+EA 7 6 3 2-4 (W88=23+EA)
INS - Input String from Port (80188+)
Usage: INS dest,port
INSB
INSW
INSD (386+)
Modifies flags: None
Loads data from port to the destination ES:(E)DI (even if a
destination operand is supplied). (E)DI is adjusted by the size
of the operand and increased if the Direction Flag is cleared and
decreased if the Direction Flag is set. For INSB, INSW, INSD no
operands are allowed and the size is determined by the mnemonic.
Clocks Size
Operands 808x 286 386 486 Bytes
dest,port - 5 15 17 1
dest,port (PM) - 5 9/29 10/32/30 1
none - 5 15 17 1
none (PM) - 5 9/29 10/32/30 1
- 386+ protected mode timings depend on privilege levels.
first number is the timing if: CPL ≤ IOPL
second number is the timing if: CPL > IOPL
third number is the timing if: virtual mode on 486 processor
INT - Interrupt
Usage: INT num
Modifies flags: TF IF
Initiates a software interrupt by pushing the flags, clearing the
Trap and Interrupt Flags, pushing CS followed by IP and loading
CS:IP with the value found in the interrupt vector table. Execution
then begins at the location addressed by the new CS:IP
Clocks Size
Operands 808x 286 386 486 Bytes
3 (constant) 52/72 23+m 33 26 2
3 (prot. mode, same priv.) - 40+m 59 44 2
3 (prot. mode, more priv.) - 78+m 99 71 2
3 (from VM86 to PL 0) - - 119 82 2
3 (prot. mode via task gate) - 167+m TS 37+TS 2
immed8 51/71 23+m 37 30 1
immed8 (prot. mode, same priv.) - 40+m 59 44 1
immed8 (prot. mode, more priv.) - 78+m 99 71 1
immed8 (from VM86 to PL 0) - - 119 86 1
immed8 (prot. mode, via task gate) - 167+m TS 37+TS 1
INTO - Interrupt on Overflow
Usage: INTO
Modifies flags: IF TF
If the Overflow Flag is set this instruction generates an INT 4
which causes the code addressed by 0000:0010 to be executed.
Clocks Size
Operands 808x 286 386 486 Bytes
none: jump 53/73 24+m 35 28 1
no jump 4 3 3 3
(prot. mode, same priv.) - - 59 46 1
(prot. mode, more priv.) - - 99 73 1
(from VM86 to PL 0) - - 119 84 1
(prot. mode, via task gate) - TS 39+TS 1
INVD - Invalidate Cache (486+)
Usage: INVD
Modifies flags: none
Flushes CPU internal cache. Issues special function bus cycle
which indicates to flush external caches. Data in write-back
external caches is lost.
Clocks Size
Operands 808x 286 386 486 Bytes
none - - - 4 2
INVLPG - Invalidate Translation Look-Aside Buffer Entry (486+)
Usage: INVLPG
Modifies flags: none
Invalidates a single page table entry in the Translation
Look-Aside Buffer. Intel warns that this instruction may be
implemented differently on future processors.
Clocks Size
Operands 808x 286 386 486 Bytes
none - - - 12 2
- timing is for TLB entry hit only.
IRET/IRETD - Interrupt Return
Usage: IRET
IRETD (386+)
Modifies flags: AF CF DF IF PF SF TF ZF
Returns control to point of interruption by popping IP, CS
and then the Flags from the stack and continues execution at
this location. CPU exception interrupts will return to the
instruction that cause the exception because the CS:IP placed
on the stack during the interrupt is the address of the offending
instruction.
Clocks Size
Operands 808x 286 386 486 Bytes
iret 32/44 17+m 22 15 1
iret (prot. mode) - 31+m 38 15 1
iret (to less privilege) - 55+m 82 36 1
iret (different task, NT=1) - 169+m TS TS+32 1
iretd - - 22/38 15 1
iretd (to less privilege) - - 82 36 1
iretd (to VM86 mode) - - 60 15 1
iretd (different task, NT=1) - - TS TS+32 1
- 386 timings are listed as real-mode/protected-mode
| |